VIA Technologies EITX-3000 Manual do Utilizador

user manual EITX-3000 Em-ITX Form Factor SBC 101-11112009-0930

X

90 EM-IO CONNECTOR PIN DEFINITION Em-IO connector Pin definition The Em-IO expansion bus interface uses the Samtec Q STRIP QSE Series 160-pin socket

91 A42 GNDGNDGNDGND GNDGNDGNDGND B42 A43 A_PCIE_TX1- B_PCIE_CLK2- B43 A44 A_PCIE_TX+ B_PCIE_CLK2+ B44 A45 GNDGNDGNDGND GNDGNDGNDGND B45

92 SELECTION OF EM-IO EXPANSION MODULES Faster Time to Market Cycles VIA has also designed a selection of expansion modules covering a variety of in

93 EMIO-3210 Em-IO Card with 6 COM Ports and 2 Parallel Ports The EMIO-3210 supports six serial ports (6 RS-232/422/485 ports, configurable in BIOS

1 1 Product Overview

2 The VIA EITX-3000 is a high performance single board computer (SBC) with low power requirements based on the Embedded ITX (Em-ITX) form factor. I

3 SPECIFICATIONS Processor Core Logic System CPUCPUCPUCPU • VIA Nano Ultra Low Voltage Processor, compact 21 mm x 21 mm NanoBGA2 package:

4 Gigabit Ethernet ControllerControllerControllerController • Onboard two VIA VT6130 Gigabit Ethernet controllers InterfaceInterfaceInterfaceInte

5 Watchdog Timer OutputOutputOutputOutput • System reset IntervalIntervalIntervalInterval • Programmable 1~255 sec. System Expansion Onb

6 Onboard DC to DC Power Supply Power ConsumptionPower ConsumptionPower ConsumptionPower Consumption • Typical 18.5W, Maximum 25.8W Input Vol

7 EITX-3000 DIMENSIONS Top Layer Bottom Layer

8 Top Layer with heatsink Bottom Layer with heatsink

9 Front I/O with heatsink Rear I/O with heatsink

II Copyright and Trademarks Copyright © 2009 VIA Technologies Incorporated. All rights reserved. No part of this document may be reproduced, transm

10 EITX-3000 LAYOUT (TOP) ItemItemItemItem DescriptionDescriptionDescriptionDescription ItemItemItemItem DescriptionDescriptionDescri

11 EITX-3000 LAYOUT (BOTTOM) SymbolSymbolSymbolSymbol DescriptionDescriptionDescriptionDescription 23 VIA Nano CPU 24 VIA VX800 system

12 FRONT I/O LAYOUT SymbolSymbolSymbolSymbol DescriptionDescriptionDescriptionDescription 26 Power button (Power On/Off) 27 Power input

13 USB Port Connector: USB Port 1 and 2 The EITX-3000 can support up to six USB-interface connectors. By default it provides two USB interface by on

14 COM Port Connectors The EITX-3000 board provides four D-Sub 9-pin connectors as COM 1, COM 2, COM 3 and COM 4 serial communications. COM 1 and

15 COM 3 and COM 4 ports The EITX-3000 provides two D-Sub 9-pin connectors, which offers standard RS-232 serial communications interface port as COM

16 REAR I/O LAYOUT SymbolSymbolSymbolSymbol DescriptionDescriptionDescriptionDescription 36 VGA port 37 LVDS port 1 38 LVDS port 2 39

17 LVDS Connectors: LVDS1 and LVDS2 The EITX-3000 supports two 24-bit single channel LVDS interface connectors by two D-Sub 26-pin connectors as “LV

18 LVDS2LVDS2LVDS2LVDS2 Pin Signal Pin Signal 1 +LCLK2 14 GND 2 -LCLK2 15 +LD2C3 3 GND 16 -LD2C3 4 +LD2C2 17 GND 5 -LD2C2 18 GN

19 LAN ports: Gigabit Ethernet Port 1 and 2 The EITX-3000 is equipped with two high performance of 1 Lane of PCI-Express bus interface of VIA VT6130

III Safety Precautions Do’s o Always read the safety instructions carefully. o Keep this User's Manual for future reference. o All caut

20

21 2 Onboard Connectors & Slots This chapter provides you with information about hardware installation procedures. It is recommended to use a gr

22 TOPSIDE CONNECTORS AND SLOTS System Fan: SYS Fan The SYS_FAN runs on +12V and maintain system cooling. When connecting the wire to the SYS FAN co

23 SATA Connectors : SATA1 and SATA2 The EITX-3000 board supports two Serial ATA ports via two onboard connectors (SATA1 and SATA2). Data transfer r

24 SATA-Power Connectors: S-Power 1 and S-Power 2 The mainboard supports two 3-pin SATA power connectors with 5V power sources: S-Power 1 and S

25 LVDS LCD Panel connector: PANEL Besides the two 24-bit single channel LVDS ports (LVDS1 and LVDS2) on the rear I/O panel, the EITX-3000 also supp

26 SODIMM SDRAM Memory slot The EITX-3000 provides one 200-pin SODIMM SDRAM slot for DDR2 533/667 MHz memory modules. It can support memory sizes up

27 Installing the memory SSSStep 1tep 1tep 1tep 1 Locate the SODIMM slot in the mainboard and align the notch on the SODIMM wi

28 USB connectors The EITX-3000 can support up to six USB ports. In addition to the two mini-DIN USB2.0 ports (USB_0/1) on the front I/O panel, the

29 USB_4/5 pin connector The USB_4/5 interface can be accessed through the 10-pin USB pin-header. It also requires an adapter cable in order to use

IV EITX-3000 Series Model Part NumberPart NumberPart NumberPart Number DescriptionDescriptionDescriptionDescription EITX-3000-1N13A1 VIA N

30 LPT pin connector The LPT port is used to connect the board to a printer. The board includes a multi-mode (EPP+ECP/ECP/EPP/SPP) parallel port acc

31 Digital I/O pin connector: DIO The board supports 8-bit Digital I/O (GPIO) through the DIO pin-header. The 8 digital inputs and outputs can be pr

32 Front Panel Audio pin connector: F_Audio The F_Audio interface enables access to the VIA High Definition Audio signals through a 10-pin (2x5-pin)

33 SPI pin connector: JSPI This SPI (Serial Peripheral Interface) pin-header is used to connect to the SPI BIOS programming fixture. Pin Signal P

34 Em-IO Expansion Connector The Em-IO interface connector enables the EITX-3000 to connect to Em-IO expansion modules. Note:Note:Note:Note: F

35 BOTTOM SIDE CONNECTORS AND SLOTS Compact Flash slot: CF Installing CF card: Step 1Step 1Step 1Step 1 Locate the CF card slot at the bottom o

36 Step Step Step Step 3333 Then gently insert the CF card and push it until it is totally inserted.

37 3 Onboard Jumpers

38 The EITX-3000 mainboard provides jumpers for setting some mainboard functions. This section will explain how to change the settings of the mainbo

39 AT/ATX POWER MODE SELECT The EITX-3000 supports two kinds of power modes: ATX (default) and AT. The ATX mode requires a standby power connection

V TABLE OF CONTENTS 1 Product Overview... 1 Key Feature

40 PVDD1_SEL: LCD POWER JUMPER The EITX-3000 Em-ITX SBC provides an onboard jumper named “PVDD1_SEL” for setting the LCD signal power to either 5V o

41 PVDD2_SEL: LCD POWER JUMPER The EITX-3000 Em-ITX SBC provides an onboard jumper named “PVDD2_SEL” for setting the LCD signal power to either 5V o

42 RST: SYSTEM RESET JUMPER To restart the hardware, momentarily close the jumper of the 2-pin reset pin-header. Setting 1 2 Open (default) OFF

43 4 BIOS Setup This chapter gives a detailed explanation of the BIOS setup functions.

44 ENTERING THE BIOS SETUP MENU Power on the computer and press <DeleteDeleteDeleteDelete> during the beginning of the boot sequence to enter

45 NAVIGATING THE BIOS MENUS The main menu displays all the BIOS setup categories. Use the <LeftLeftLeftLeft>/<RightRightRightRight> and

46 MAIN MENU The Main Menu contains thirteen setup functions and two exit choices. Use arrow keys to select the items and press <EnterEnterEnterE

47 PC Health Status This menu shows the PC health status. Frequency/Voltage Control Use this menu to set the system frequency and voltage control. L

48 STANDARD CMOS FEATURES Date The date format is [Day, Month, Date, Year] Time The time format is [Hour : Minute : Second] Video Settings: [EGA/VG

49 IDE CHANNELS The specifications of your drive must match with the drive table. The hard disk will not work properly if you enter incorrect info

VI Bottom side connectors and slots...35 Compact Flash slot: CF...

50 ADVANCED BIOS FEATURES Virus Warning Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection. Settings Descript

51 First/Second/Third Boot Device Set the boot device sequence as BIOS attempts to load the disk operating system. Settings Description LS120 Boot

52 Security Option Selects whether the password is required every time the System boots, or only when you enter Setup. Settings Description Setup

53 CPU FEATURE Thermal Management This item sets CPU’s thermal control rule to protect CPU from overheat. Settings Description Thermal Monitor 1

54 HARD DISK BOOT PRIORITY This is for setting the priority of the hard disk boot order when the “Hard Disk” option is selected in the “[First/Seco

55 ADVANCED CHIPSET FEATURES Caution:Caution:Caution:Caution: The Advanced Chipset Features menu is used for optimizing the chipset functions. D

56 INTERNAL VGA CONTROL VGA Share Memory Size This setting allows you to select the amount of system memory that is allocated to the integrated gra

57 CPU & PCI BUS CONTROL PCI Master 0 WS Write Settings: [Disabled, Enabled] PCI Delay Transaction Settings: [Disabled, Enabled] VIA PWR Manage

58 INTEGRATED PERIPHERALS

59 VIA ONCHIP IDE DEVICE CF Card ATA66 Settings: [Disabled, Enabled] SATA Controller Settings: [Disabled, Enabled] IDE DMA Transfer Access Settings

VII Security Option...52 MPS Version Control for OS...

60 Secondary Master UDMA Settings: [Disabled, Auto] Secondary Slave UDMA Settings: [Disabled, Auto] IDE HDD Block Mode Settings: [Disabled, Enabled]

61 VIA ONCHIP PCI DEVICE Azalia HDA Controller Settings: [Disabled, Auto] OnBoard LAN Boot ROM Settings: [Enabled, Disabled]

62 SUPERIO DEVICE Onboard Parallel Port Settings: [Disabled, 378/IRQ7, 278/IRQ5, 3BC/IRQ7] Parallel Port Mode Settings: [SPP, EPP, ECP, ECP+EPP] Wa

63 SUPERIO COM PORTS (UARTS) Onboard Serial Port 1 Settings: [Disabled, 3F8/IRQ4, 2F8/IRQ4, 3E8/IRQ4, 2E8/IRQ4] COM1 RS232/422/485 Type Settings: [

64 USB DEVICE SETTING USB 1.0 Controller Enable or disable Universal Host Controller Interface for Universal Serial Bus. Settings: [Disabled, Enabl

65 USB Storage Function Enable or disable Legacy support of USB Mass Storage. Settings: [Disabled, Enabled] USB Wireless LAN Support Settings: [Disa

66 POWER MANAGEMENT SETUP ACPI Suspend Type Settings Description S1(POS) S1/Power On Suspend (POS) is a low power state. In this state,

67 Video Off Option Select whether or not to turn off the screen when system enters power saving mode, ACPI OS such as Windows XP will override this

68 WAKEUP EVENT DETECT PowerOn by PCI Card Enables activity detected from any PCI card to power up the system or resume from a suspended state. Su

69 PNP/PCI CONFIGURATIONS Note:Note:Note:Note: This section covers some very technical items and it is strongly recommended to leave the defaul

VIII Watch Dog Timer Select ...62 SuperIO COM Ports (UARTs)...

70 Resources Controlled By Enables the BIOS to automatically configure all the Plug-and-Play compatible devices. Settings Description Auto(ESCD) B

71 PC HEALTH STATUS The PC Health Status displays the current status of all of the monitored hardware devices/components such as CPU voltages, temp

72 FREQUENCY/VOLTAGE CONTROL DRAM Frequency Settings: [DDR2-400, DDR2-533, DDR2-667, SPD] DDR CAS Latency Control Settings: [2T, 3T, 4T, 5T, 6T, SP

73 Spread Spectrum When the mainboard's clock generator pulses, the extreme values (spikes) of the pulses create EMI (Electromagnetic Interfere

74 LOAD OPTIMIZED DEFAULTS This option is for restoring all the default optimized BIOS settings. The default optimized values are set by the mainbo

75 SET SUPERVISOR/USER PASSWORD This option is for setting a password for entering BIOS Setup. When a password has been set, a password prompt wil

76 SAVE & EXIT SETUP Entering “YYYY” saves any changes made, and exits the program. Entering “NNNN” will cancel the exit request.

77 EXIT WITHOUT SAVING Entering “YYYY’ discards any changes made, and exits the program. Entering “NNNN” will cancel the exit request.

78

79 5 Driver Installation This chapter gives you brief descriptions of each mainboard driver and application. You must install the VIA chipset driver

IX Frequency/Voltage Control...72 DRAM Frequency ...

80 DRIVER UTILITIES Getting Started The EITX-3000 includes a driver CD that contains the drivers and software for enhancing the performance of the s

81 CD CONTENT  VIA VIA VIA VIA Hyperion Pro DriverHyperion Pro DriverHyperion Pro DriverHyperion Pro Driver  Compatible with all current VIA

82

83 A Disassembling the EITX-3000 Board from Heatsink

84 DISASSEMBLING Step 1Step 1Step 1Step 1 Unscrew the seven screws on the EITX-3000 mainboard. Step Step Step Step 2222 Gently pull

85 Step Step Step Step 3333 When installing the EITX-3000 into the casing, change the screws with the longer screws in order to secure it with th

86

87 B EM-IO : Embedded IO Expansion Bus Interface

88 INTRODUCTION The Flexible Embedded Board with Em-IO Expansion For embedded system developers, flexibility in I/O configurations is necessary in o

89 Modularized Expansion of Em-IO Interface The Em-IO interface connector is an open bus interface initiated by VIA at the end of 2008. The Em-IO i